Garage
Wood stove clearance to wall
The 36 in rule is real, but it is the rule for a stove nobody tested. A tested stove carries its own number.
On this page (9 sections)
- What clearance to combustibles means, and where it is measured
- Where 36 in comes from, and why it is only the fallback
- A listed stove: 6 1/2 to 21 1/2 in, read from the label
- Stovepipe: 18 in for single-wall, less only if the manual says
- A shield cuts 36 in to 12 in, and the IRC stops it there
- Worked through: a stove in the back corner of a garage workshop
- The garage rules: 18 in up, clear of cars, away from fuel
- Floor protection: 16 in in front, 8 in to the sides, none on bare slab
- Where these figures stop applying
Short answer
36 in (914 mm) from a combustible wall for a radiant wood stove with no listing label, in the NFPA 211 table that Maine's State Fire Marshal prints. A sheet-steel shield spaced 1 in (25 mm) off the wall cuts that to 12 in (305 mm), and the IRC lets no shield go lower. A listed stove uses the figures on its label: 6 1/2 to 21 1/2 in (165 to 546 mm) across the five checked here. Single-wall stovepipe needs 18 in (457 mm).
The numbers, at a glance
- Unlisted radiant stove to an unprotected wall
- 36 in (914 mm)NFPA 211 table, as printed by the Maine State Fire Marshal
- Same stove, steel shield 1 in off the wall
- 12 in (305 mm)IRC Table M1306.2, sides and rear
- Lowest any shield can take a stove
- 12 in (305 mm)IRC M1306.2.3; no cut at all for labels of 12 in or less
- Listed stoves, unit to side wall
- 12 3/4 to 21 1/2 in (324 to 546 mm)Blaze King, Pacific Energy, Drolet, Englander
- Listed stoves, unit to rear wall
- 6 1/2 to 20 in (165 to 508 mm)Same five stoves
- Alderlea T5 with double-wall pipe
- 14 in side, 5 in rear (356, 127 mm)Against 18 and 12 in with single-wall
- Single-wall stovepipe to combustibles
- 18 in (457 mm)IRC Table M1803.3.4
- Floor protector on a combustible floor, US
- 16 in front, 8 in sides (406, 203 mm)Measured from the loading door
- Ignition source above a garage floor
- 18 in (457 mm)IRC M1307.3
A wood stove with no listing label needs 36 in (914 mm) from any wall that can burn. That is the radiant stove figure in the NFPA 211 table, as the Maine State Fire Marshal prints it. A sheet-steel shield, spaced 1 in (25 mm) off the wall, cuts that to 12 in (305 mm), and the IRC lets no shield go lower. A listed stove ignores the 36 in and uses the numbers on its label. The five checked here ask 6 1/2 to 21 1/2 in (165 to 546 mm) at the back and sides. Single-wall stovepipe needs 18 in (457 mm). The worked case is a stove in a garage workshop, and the rest of that room is on the garage hub.
What clearance to combustibles means, and where it is measured#
A clearance to combustibles is the air gap a hot appliance needs from anything that can burn. NIST notes that wood heated for a long time may change and catch fire at a much lower heat, so the gap is set to keep the wall cool, not just unburnt.
The IRC measures it "from the surface of the heat-producing appliance" to "the outer surface of the combustible material": from the stove's body to the face of the wall, square off it, as the site's measuring method describes.
Three more terms decide which number is yours, and others are in the glossary.
- A combustible wall is any wall that can burn. Maine's guide counts only solid masonry or corrugated steel as non-combustible, and says "merely covering a wood studded wall with a non-combustible material" does not change that.
- A listed stove has been tested by a lab and carries a label with its own clearances. In the US the test is UL 1482. An unlisted stove has no label, which is common on old or home-built stoves.
- A radiant stove throws heat straight out from its hot metal skin. A circulating stove has an outer jacket with room air flowing through it, and Maine's table gives it smaller side and rear gaps.
Where 36 in comes from, and why it is only the fallback#
Maine's installation guide prints Table 1 from NFPA 211 (1996 edition), the fire standard for chimneys and solid-fuel appliances. These are its minimums with no added wall protection.
| Appliance | Front | Sides | Rear | Ceiling |
|---|---|---|---|---|
| Radiant stove | 36 in (914 mm) | 36 in (914 mm) | 36 in (914 mm) | 36 in (914 mm) |
| Circulating stove | 24 in (610 mm) | 12 in (305 mm) | 12 in (305 mm) | 36 in (914 mm) |
| Listed stove | Maker's figures | Maker's figures | Maker's figures | Maker's figures |
The last row matters most. Maine says listed stoves go in "according to manufacturers' recommendations." The 2021 IRC agrees in M1306.1: clearances are "as indicated on the appliance label and in the manufacturer's installation instructions."
The IRC also asks for the test. Section M1410.1, in chapter 14, says solid-fuel room heaters "shall be tested in accordance with" UL 1482, and a stove with no label has nothing to show that test. Where a town uses the IRC, a new unlisted stove is the inspector's call, and 36 in is the least you can plan around.
Why does 36 in turn up on so many pages, then? Because it fits every stove. NIST's 1982 report says codes give "a single (hopefully conservative) clearance" for each type of stove, with no allowance for size or heat output, and that its experimental basis "is not, however, quite so clear."
A listed stove: 6 1/2 to 21 1/2 in, read from the label#
Five listed stoves, from four makers, with single-wall pipe:
| Stove | Unit to side wall | Unit to rear wall | Corner | With double-wall pipe |
|---|---|---|---|---|
| Blaze King Chinook CK20.2 | 12 3/4 in (324 mm) | 6 1/2 in (165 mm) | 6 in (152 mm) | Same figures in the US |
| Englander 15-W03 | 21 1/2 in (546 mm) | 7 1/2 in (191 mm) | 9 1/2 in (241 mm) | No figures given |
| Pacific Energy Alderlea T5 | 18 in (457 mm) | 12 in (305 mm) | 11 in (279 mm) | 14 in, 5 in, 4 in (356, 127, 102 mm) |
| Drolet Eastwood 1800 | 18 in (457 mm) | 18 in (457 mm) | 12 in (305 mm) | Same figures |
| Drolet Eastwood 1500 | 19 in (483 mm) | 20 in (508 mm) | 14 in (356 mm) | Same figures |
Every one beats 36 in, and two of them by far at the back, because the lab sets each figure from the wall's temperature: NIST gives the limit as a rise of no more than 65 °C (117 °F) above the room on an exposed surface. Englander's manual is the Canadian edition, tested to ULC S627, while the other three makers list UL 1482 as well.
The figures do not follow the stove's size. The Englander wants the most at the side and almost the least at the back, while the Drolet 1800 wants the same at both. The corner figure runs from the stove's nearest corner to the wall, with the stove set at 45 degrees.
Stovepipe: 18 in for single-wall, less only if the manual says#
The connector is the stovepipe from the stove to the chimney, and it has its own gap. Single-wall pipe is one sheet of steel; double-wall pipe has a second skin with air between. IRC Table M1803.3.4, in chapter 18, gives 18 in (457 mm) from single-wall pipe on a solid-fuel appliance. Maine prints the same 18 in, or "three times the diameter of the connector," which is 18 in again for a 6 in pipe.
The pipe can set the stove's place by itself: Englander asks 29 in (737 mm) from the connector to the side wall, against 21 1/2 in for the stove body.
Does double-wall pipe let the stove sit closer? Only if its manual says so, and the four makers split. Pacific Energy gives a second, smaller set: 14 in side, 5 in rear, 4 in corner. Drolet prints the same figures for both pipes. Blaze King gives one set in the US, and in Canada adds 18 in from any single-wall pipe. Englander marks every double-wall cell "N/A". So "less with double-wall" holds for one stove in four here.
One pipe rule matters in a garage. Under IRC M1803.3.1 a connector may not pass through a wall unless it is listed for that, or runs through a listed pass-through. It may never pass through a floor or ceiling.
A shield cuts 36 in to 12 in, and the IRC stops it there#
A wall shield is a non-combustible sheet held off the wall on spacers, so air can rise behind it and carry heat away. IRC Table M1306.2 lists eight kinds, and these are its figures for a stove that needs 36 in bare.
| Protection | Sides and rear | Above |
|---|---|---|
| 3 1/2 in masonry wall, no air space | 24 in (610 mm) | Not listed |
| 1/2 in insulation board over 1 in mineral wool | 18 in (457 mm) | 24 in (610 mm) |
| 24 gauge sheet steel, 1 in air space | 12 in (305 mm) | 18 in (457 mm) |
| 1/2 in insulation board, ventilated air space | 12 in (305 mm) | 18 in (457 mm) |
The steel is "No. 24 gage", at least 0.0236 in thick. The build rules are in M1306.2.2 and the table's notes. Leave at least 1 in (25 mm) of air behind it, and leave its edges open 1 in: top and bottom, or top and sides on a flat wall, and top and bottom in a corner. Use non-combustible spacers, never one directly behind the stove or pipe. Keep 1 in between stove and shield. And make it big enough that any bare wall is still the full 36 in away.
Then M1306.2.3 ends the sum. The table "shall not be used" for stoves "listed for installation with minimum clearances of 12 inches (305 mm) or less." For any other stove it may not go "to less than 12 inches."
Why the air gap? NIST heated gypsum board with a stove panel at 350 °C (660 °F). Bare board 3 in (75 mm) away caught fire. Metal plates with air behind kept the board at 36 to 44 °C (97 to 111 °F) in the same setting. Brick veneer fixed flat to the board still needed 36 in to stay in the limit.
Worked through: a stove in the back corner of a garage workshop#
Take a garage with drywall on stud walls and a bare concrete slab. Suppose the stove goes in a back corner, square to the back wall. Walk two stoves of the same size through the published figures.
A listed Drolet Eastwood 1800, 25 1/4 in wide and 25 1/8 in deep (641 x 638 mm).
- Rear: the label asks 18 in, so the front face is 18 + 25 1/8 = 43 1/8 in (1.10 m) from the back wall.
- Front: Drolet asks 48 in (1.22 m), so nothing that burns goes within 43 1/8 + 48 = 91 1/8 in (2.31 m) of the back wall.
- Side: 18 + 25 1/4 = 43 1/4 in (1.10 m) from the side wall to the far side.
- With shields, each 18 in falls to 12 in, saving 6 in each way: the front zone ends at 85 1/8 in (2.16 m), the far side at 37 1/4 in (946 mm).
An unlisted radiant stove of the same size takes 36 in at the back, so its front face is 61 1/8 in (1.55 m) out. Maine gives 36 in at the front and says in note 7 that the front is never reduced, so the zone runs to 97 1/8 in (2.47 m). Its far side is 36 + 25 1/4 = 61 1/4 in (1.56 m) from the side wall. With shields the back and side fall to 12 in: the zone ends at 12 + 25 1/8 + 36 = 73 1/8 in (1.86 m), and the far side at 37 1/4 in (946 mm).
| Case | Back wall to stove | Back wall to end of front zone | Side wall to far side |
|---|---|---|---|
| Drolet Eastwood 1800, bare walls | 18 in (457 mm) | 91 1/8 in (2.31 m) | 43 1/4 in (1.10 m) |
| Drolet Eastwood 1800, shielded | 12 in (305 mm) | 85 1/8 in (2.16 m) | 37 1/4 in (946 mm) |
| Unlisted radiant stove, bare walls | 36 in (914 mm) | 97 1/8 in (2.47 m) | 61 1/4 in (1.56 m) |
| Unlisted radiant stove, shielded | 12 in (305 mm) | 73 1/8 in (1.86 m) | 37 1/4 in (946 mm) |
The shielded unlisted stove ends with the smaller front zone, because Maine asks 36 in at its front where Drolet asks 48 in. The unlisted stove still has to get past M1410.1.
Set these against the machine zones in workshop tool clearances.
The garage rules: 18 in up, clear of cars, away from fuel#
The 18 in ignition rule. IRC M1307.3 says appliances "having an ignition source shall be elevated such that the source of ignition is not less than 18 inches (457 mm) above the floor in garages." It does not name wood stoves and gives them no exception. Ask the building official how they read it before you buy. The same rule comes up in garage heater mounting height.
Vehicles. IRC M1307.3.1 bars any appliance where a vehicle can damage it, unless barriers protect it. Keep the stove and pipe out of the bay and the door swing set out in car parking space dimensions.
Fuel. Englander says not to store or use gasoline "or other flammable vapors and liquids in the vicinity," and Pacific Energy says not to store wood within the stove's clearances.
One maker says no. Blaze King says its stoves "have been tested and certified to be installed in insulated, habitable rooms," not "a shop/garage environment." In a cold room the thermostat calls for heat all the time and over-fires the stove, and Blaze King voids the warranty for that damage.
The house wall. A pipe through the wall shared with the house needs a listed pass-through, and that wall is the fire separation in garage to house door and step.
Floor protection: 16 in in front, 8 in to the sides, none on bare slab#
On a combustible floor, three US manuals agree: the pad runs 16 in (406 mm) out from the loading door and 8 in (203 mm) past each side of the door opening.
| Stove | US front | US sides | Minimum pad |
|---|---|---|---|
| Drolet Eastwood | 16 in (406 mm) | 8 in (203 mm) | Not stated |
| Pacific Energy Alderlea T5 | 16 in (406 mm) | 8 in (203 mm) | 34 x 40 1/2 in (864 x 1,029 mm), US |
| Blaze King Chinook CK20.2 | 16 in (406 mm) | 8 in (203 mm) | 32 x 40 1/8 in (813 x 1,019 mm), US |
| Englander 15-W03 | Not stated | Not stated | 38 1/2 x 47 in (978 x 1,194 mm), Canada |
All four print the Canadian rule as well: 18 in (457 mm) at the door side and 8 in at the others.
All three US manuals also want the pad under the pipe where it runs flat, plus 2 in (51 mm) each side. The pad is for embers. Englander says "No R Value is necessary," and Blaze King asks for no thermal pad.
In a garage the slab often settles it. Drolet needs no protection on a non-combustible floor, "ex: concrete," and Maine lets a stove stand on a slab with nothing combustible fixed under it. A timber floor needs the pad. A fireplace hearth uses a similar 16 in and 8 in, set out in fireplace and media wall dimensions.
Where these figures stop applying#
These figures are for a freestanding wood stove against a combustible wall in a US home or garage, under the 2021 IRC, Maine's NFPA 211 tables and the four manuals named here. Your town may amend the code, so check with the building department, and read your own stove's label.
They do not cover inserts, pellet or gas stoves, cookstoves, mobile homes, alcoves or masonry heaters, which each have their own listing or code section. They do not cover the chimney, its ceiling clearance or its height above the roof, nor combustion air, carbon monoxide alarms or ashes. Blaze King says never to store hot ashes in a garage.
Clearance is one fire figure among several. A stove at the right distance can still start a fire through a bad chimney, over-firing or fuel stacked too close; the woodpile belongs outside, as in firewood distance from the house. Other fuel-burning equipment has its own gaps, in water heater and boiler clearances, the codes are in standards and codes, and the unit converter handles the metric.
Frequently asked questions#
How far does a wood stove need to be from a wall?
Whatever its label says, if it has one. Five listed stoves checked here ask 12 3/4 to 21 1/2 in (324 to 546 mm) at the side and 6 1/2 to 20 in (165 to 508 mm) at the back. A stove with no label falls back to the old NFPA 211 table: 36 in (914 mm) from any combustible wall for a radiant stove, 12 in (305 mm) at the sides and back for a circulating one.
Can a wood stove be 12 inches from a wall?
Yes, if the label says 12 in or less, or if a shield brings it there. The IRC lets a ventilated sheet-steel shield, spaced 1 in (25 mm) off the wall, cut a 36 in (914 mm) clearance to 12 in (305 mm). It never allows less than 12 in by shielding (M1306.2.3). Pacific Energy's Alderlea T5 reaches 12 in at the back on its own label, with no shield.
Does cement board or tile on the wall reduce wood stove clearance?
Not when it is fixed flat to the wall. The protection that earns a cut has a 1 in (25 mm) air gap behind it, open at the edges. Maine's guide says covering a wood stud wall with a non-combustible material does not make it a non-combustible wall. In the 1982 NIST tests, brick veneer fixed straight onto drywall still needed 36 in (914 mm) to keep the board cool enough.
How far does stovepipe need to be from the wall?
18 in (457 mm) for single-wall pipe from a wood stove, in IRC Table M1803.3.4. Maine's guide gives the same figure, or three times the pipe diameter, which is 18 in for a 6 in pipe. Listed double-wall pipe uses its own listing, and the stove's label still sets the stove's own gap. Blaze King lists one set of figures for both pipes in the US.
Can you put a wood stove in a garage?
The model code does not ban it, but it adds rules, and some makers say no. Blaze King writes that its stoves were not designed for a shop or garage and that the warranty is void there. IRC M1307.3 wants any ignition source 18 in (457 mm) above a garage floor. Gasoline and its vapour must stay clear, and your town may add its own rules, so ask the building department first.
How big does the hearth pad need to be for a wood stove?
In the US, 16 in (406 mm) in front of the loading door and 8 in (203 mm) to each side of the door, on Drolet, Pacific Energy and Blaze King manuals. Canada asks 18 in (457 mm) in front and 8 in at the other sides. On a bare concrete slab Drolet needs no pad at all. Blaze King's minimum US pad is 32 x 40 1/8 in (813 x 1,019 mm).
Does double-wall pipe let a wood stove sit closer to the wall?
Only if the manual says so. Pacific Energy's Alderlea T5 drops from 18 to 14 in (457 to 356 mm) at the side and from 12 to 5 in (305 to 127 mm) at the back with double-wall pipe. Drolet's Eastwood prints the same figures for both pipes. Englander's 15-W03 gives no double-wall figures at all. The label is the only place to find out.
How high above a wood stove does the ceiling need to be?
36 in (914 mm) above a radiant stove with no label, by the NFPA 211 table. Listed stoves vary: Blaze King asks 37 in (940 mm) from the Chinook's top, and Drolet asks 84 in (2.13 m) from the floor to the ceiling for the Eastwood, which a standard 8 ft (2.44 m) garage ceiling clears. Check the label for yours.
Sources and standards referenced#
- Recommended standards for the installation of woodburning stoves Maine Office of State Fire Marshal and Office of Energy Resources (NFPA 211, 1996 edition)Table 1: radiant stove 36 in ceiling, front, side and rear; circulating 36/24/12/12 in; stovepipe 18 in; listed stoves to the maker's instructions. Table 2: 24 gauge sheet metal with ventilated air space cuts 36 in to 12 in; 1 in air gap; front clearance not reduced. Concrete slab needs no floor protection; connector three times its diameter
- Evaluation of wall protection systems for wood heating appliances, NBSIR 82-2506 J. J. Loftus, National Bureau of Standards (now NIST), May 1982Codes typically specify 36 in for radiant heaters, 18 in for single-wall connectors; experimental basis 'not so clear'; listings limit wall temperature rise to 65 C exposed, 50 C behind protectors; gypsum wallboard ignited at 3 in with a 350 C stove; metal plate and air space most effective; brick veneer fixed to the board needed 36 in
- International Residential Code 2021: M1306.1, M1306.2, Table M1306.2, M1306.2.2, M1306.2.3, M1307.1, M1307.3, M1307.3.1 (chapter 13); M1410.1, M1410.2 (chapter 14); M1803.3.1, Table M1803.3.4 (chapter 18) International Code Council, via UpCodes (Colorado)Label clearances govern; sheet steel 1 in off the wall cuts 36 in to 12 in sides and rear, 18 in above; no shield below 12 in, none at all for labels of 12 in or less; solid-fuel room heaters tested to UL 1482; noncombustible floor 18 in all round for unlisted heaters; ignition source 18 in above a garage floor; single-wall connector 18 in
- 15-W03 installation and operation manual, 46327A (2023) Englander (Stove Builder International)22 x 27 x 30 in; single-wall connector: unit to side wall 21.5 in, rear 7.5 in, corner 9.5 in, connector to side wall 29 in; 17.5 in side and 5.5 in corner with side shields; double-wall N/A; Canadian floor protector 18 in front, 8 in sides and rear
- Alderlea T5 installation and operation guide Pacific EnergyTested and listed to CAN/ULC S627 and UL 1482; single-wall connector: 18 in side, 12 in rear, 11 in corner; double-wall: 14 in, 5 in, 4 in; US floor protector 16 in front and 8 in to the sides of the loading door, 34 x 40 1/2 in minimum
- Eastwood 1500 and 1800 EPA wood stoves owner's manual DroletSame clearances with single- or double-wall pipe: Eastwood 1800 rear 18 in, side 18 in, corner 12 in, 48 in in front, 84 in floor to ceiling; Eastwood 1500 rear 20, side 19, corner 14 in; US floor protector 16 in front, 8 in sides; none on concrete; shield cuts of 67 per cent sides and rear
- Chinook CK20.2 owner's manual, 180-CK20.2 v3.01 (Feb 2025) Blaze KingSide wall 12.75 in, rear 6.5 in, corner 6 in, stove top to ceiling 37 in; US floor shield 16 in front, 8 in sides, 32 x 40.125 in minimum; not designed for a shop or garage, warranty void there
We cite published codes, industry planning guidelines and manufacturer specifications. Where a figure is our own recommendation rather than a published standard, the text says so. See how we measure.