Garage
Pellet stove clearance to wall
A pellet stove can stand almost against the wall because a lab tested it there. The 36 in rule is for a stove nobody tested.
On this page (8 sections)
- What clearance to wall means for a pellet stove
- Seven pellet stoves: 0 to 5 in at the back, 6 to 13 in at the side
- Why a pellet stove sits at 0 to 5 in when a wood stove needs 36 in
- The vent pipe: 1 to 3 in from the wall, more where it ends outside
- Floor protection: 6 in in front, 2 to 6 in at the sides
- Worked through: a Castle Serenity against an outside wall
- In a garage: where the air comes from and where the vent ends
- Where these figures stop applying
Short answer
0 to 5 in (0 to 127 mm) from the back wall and 6 to 13 in (152 to 330 mm) from a side wall, across seven pellet stoves from five makers. Two Englanders ask 0 in at the back. The pellet vent pipe then needs 1 to 3 in (25 to 76 mm) of its own, and it often sets the back gap. The floor pad runs 6 in (152 mm) in front. An unlisted wood stove needs 36 in (914 mm), because nobody tested it.
The numbers, at a glance
- Stove to back wall
- 0 to 5 in (0 to 127 mm)Englander 25-CB120 and 25-CBPAH 0 in; Castle Serenity 5 in
- Stove to side wall
- 6 to 13 in (152 to 330 mm)Englander 25-PDVC and Quadra-Fire Mt. Vernon AE 6 in; PelPro PP130 13 in
- Stove corner to wall, set at 45 degrees
- 2 to 10 in (51 to 254 mm)Six of the seven give a figure
- Pellet vent pipe to combustibles
- 1 to 3 in (25 to 76 mm)DuraVent 1 in; Comfortbilt 2 in; PelPro and Quadra-Fire 3 in
- Floor pad in front of the stove
- 6 in (152 mm)Measured from the glass on three of the seven
- Floor pad at the sides
- 2 to 6 in (51 to 152 mm)PelPro and Quadra-Fire 2 in; the rest 6 in
- Unlisted wood stove, for contrast
- 36 in (914 mm)NFPA 211 table, as printed by the Maine State Fire Marshal
- Ignition source above a garage floor
- 18 in (457 mm)IRC M1307.3
A pellet stove needs 0 to 5 in (0 to 127 mm) from the back wall and 6 to 13 in (152 to 330 mm) from a side wall. Those are the figures on seven stoves from five makers, and two Englanders ask 0 in at the back. The vent pipe needs 1 to 3 in (25 to 76 mm) of its own, and it often decides how far out the stove really sits. The floor pad runs 6 in (152 mm) past the front. An unlisted wood stove needs 36 in (914 mm), as wood stove clearance to wall sets out, and the difference is a lab test. The rest of the room is on the garage hub.
What clearance to wall means for a pellet stove#
A pellet stove burns small pellets of pressed sawdust. They sit in a hopper, and a screw called an auger feeds them into a small burn pot a few at a time, as Castle's manual describes. A fan, the exhaust motor, pulls the hot gas through a heat exchanger and out through the vent. A second fan, the room air blower, pushes room air around the heat exchanger and out into the room.
A clearance to combustibles is the air gap a hot appliance needs from anything that can burn. A drywall wall on wood studs counts, even when it is painted or tiled, and the IRC sends you to the label for the gap: "as indicated on the appliance label and in the manufacturer's installation instructions" (M1306.1).
Three more terms decide which number is yours, and others are in the glossary.
- A listed stove has been tested by a lab and carries a label with its own gaps. All seven here name their test. Castle says its gaps were "established by the ASTM testing lab."
- Pellet vent is the exhaust pipe. Castle calls it Type L: two layers of steel with air between, which keeps the outer skin cool enough to sit close to a wall.
- A floor protector, or hearth pad, is the non-combustible sheet under the stove. On a pellet stove it is there to catch embers.
Each gap runs from the stove's body to the face of the wall, square off it, as the site's measuring method describes. The corner figure is for a stove set at 45 degrees across a corner, and it runs from each back corner of the stove to the nearest wall.
Seven pellet stoves: 0 to 5 in at the back, 6 to 13 in at the side#
These are the gaps for a stove vented straight out through the back wall, which is the usual way. Each comes from the maker's manual or label.
| Stove | Side wall | Back wall | Corner, at 45 degrees |
|---|---|---|---|
| Englander 25-CB120 | 10 in (254 mm) | 0 in | 10 in (254 mm) |
| Englander 25-CBPAH | 8 in (203 mm) | 0 in | 6 in (152 mm) |
| Englander 25-PDVC | 6 in (152 mm) | 3 in (76 mm) | Not given |
| Castle Serenity | 7 in (178 mm) | 5 in (127 mm) | 5 in (127 mm) |
| Comfortbilt HP22 | 7 in (178 mm) | 2 in (51 mm) | 5 in (127 mm) |
| PelPro PP130 | 13 in (330 mm) | 2 in (51 mm) | 3 in (76 mm), vertical vent |
| Quadra-Fire Mt. Vernon AE | 6 in (152 mm) | 2 in (51 mm) | 2 in (51 mm) |
The 25-CBPAH figures are from its own Englander manual, revised in 2019. The Mt. Vernon figures are read from the sample safety label printed in its manual.
Three things stand out. First, the back gap is small on every stove, and the side gap is always the larger one. Second, the side gap does not follow a brand: Englander's three stoves ask 6, 8 and 10 in. Third, no two stoves share all three figures, so a gap read off a forum or a different model is a guess.
One manual disagrees with itself. Castle's clearance page draws 5 in at the back. Its floor page says that, with the clean-out tee outside, "the minimum clearance is 2" from the back of the stove to the wall." Take the larger figure, 5 in, until the maker tells you otherwise.
Why a pellet stove sits at 0 to 5 in when a wood stove needs 36 in#
The 36 in figure is real: it is the radiant stove row in the NFPA 211 table, as the Maine State Fire Marshal prints it: 36 in at the front, sides, back and ceiling. But it is the gap for a stove with no label. The same table sends listed stoves to "Manufacturers Recommendations."
So the two numbers answer different questions: 36 in is a safe guess for a stove nobody has measured. 0 to 5 in is what a lab found when it ran a particular pellet stove beside a test wall. The wood stove page explains the test limit: the wall may warm only so far above the room.
A pellet stove passes that test close to the wall for reasons its manuals describe.
- The fire is small and metered. The auger feeds a set rate. Englander's 25-PDVC burns 2.2 to 3.8 lb (1.0 to 1.8 kg) of pellets an hour, and the Castle's input is 4.0 lb an hour.
- The heat goes out of the front. The room air blower pushes warm air forward into the room, so less of it soaks into the back panel.
- The exhaust is pushed by a fan. It leaves through a sealed, double-wall vent, not a hot single-wall stovepipe. A wood stove's single-wall pipe needs 18 in (457 mm) by itself.
That last point is also why the back gap can grow. The stove may be cool at the back, but the vent comes out of the back.
The vent pipe: 1 to 3 in from the wall, more where it ends outside#
The pipe has its own gap, separate from the stove's. DuraVent's PelletVent guide says the pipe "is UL listed for 1" clearance to combustibles in the USA." It also says to keep that 1 in (25 mm) in Canada. The stove makers often ask more near their own outlet.
| Where | Gap | Source |
|---|---|---|
| Pellet vent pipe to combustibles | 1 in (25 mm) | DuraVent PelletVent |
| Back wall and side wall to the pipe, vertical vent | 2 in (51 mm) | Comfortbilt HP22 |
| Back wall to the pipe, vertical vent | 3 in (76 mm) | PelPro PP130, Quadra-Fire Mt. Vernon AE |
| Pipe to the outside wall, once through it | 3 in (76 mm) | Englander 25-PDVC |
| Vent end, sideways from a combustible wall | 12 in (305 mm) | Englander, Comfortbilt |
Where the pipe and the stove ask for different figures, use the larger. And where the pipe passes through a wall, Englander says to "USE an approved wall thimble," which is a listed sleeve that holds the gap inside the wall.
Where the pipe ends outside matters too. Englander's 25-CB120 lists the limits: 4 ft (1.22 m) below or beside a door or window that opens, 1 ft (305 mm) above one, 2 ft (610 mm) from the next building and above grass, 3 ft (914 mm) from a forced-air intake, and 7 ft (2.13 m) above a public walkway. Window heights are in window sill and head heights, and the outdoor units of a heat pump in HVAC and air handler clearances.
Floor protection: 6 in in front, 2 to 6 in at the sides#
On a floor that can burn, the stove stands on a pad that reaches past it on each side. The front is measured from the glass on three stoves.
| Stove | Front | Sides | Back | What the pad must be |
|---|---|---|---|---|
| Englander 25-CB120, US | 6 in (152 mm) | 6 in (152 mm) | 4 in (102 mm) | R-value 0.2 or more |
| Englander 25-CBPAH | 6 in (152 mm) | 6 in (152 mm) | Not stated | Non-combustible |
| Englander 25-PDVC | 6 in (152 mm) | 6 in (152 mm) | Not stated | Embers only, no R-value |
| Castle Serenity | 6 in (152 mm) | 6 in (152 mm) | 2 in (51 mm) | 24 gauge sheet metal at least |
| Comfortbilt HP22 | 6 in from the glass | 6 in (152 mm) | 2 in past the pipe | Non-combustible |
| PelPro PP130, US | 6 in from the glass | 2 in (51 mm) | 2 in (51 mm) | Non-combustible |
| Quadra-Fire Mt. Vernon AE | 6 in from the glass | 2 in (51 mm) | 2 in (51 mm) | Non-combustible |
A wood stove pad is much larger: 16 in (406 mm) in front and 8 in (203 mm) at the sides on three US manuals, as the wood stove page shows.
One maker asks two things. Englander's 25-PDVC calls its pad "spark and ember protection only," with "no required R value." Its 25-CB120 asks for an R-value of 0.2 or more. It says two sheets of 1/2 in cement board under tile meet that. Read the pad rule in your own manual, not a sister model's.
Canada asks for more in front. Englander's 25-CB120 gives 18 in (457 mm) in front and 8 in (203 mm) at the sides, and its 25-PDVC 450 mm in front.
A bare slab often needs nothing. Englander's 25-PDVC says a brick or concrete floor needs no floor protection. The 25-CB120 adds the 0.2 R-value test, with "a concrete floor in a basement" as its example. For the room around the pad, the fireplace and media wall page gives the hearth figures for a built-in fire.
Worked through: a Castle Serenity against an outside wall#
Take a living room with drywall on stud walls and a carpeted floor. Suppose a Castle Serenity goes against the outside wall, near a side wall. The vent goes straight out through the back, with the clean-out tee outside. The stove is 18 1/4 in wide and 23 3/4 in deep (464 x 603 mm). Walk it through the published figures.
- Back. The clearance page asks 5 in (127 mm), so the front of the stove sits 5 + 23 3/4 = 28 3/4 in (730 mm) from the back wall.
- Side. Castle asks 7 in (178 mm), so the stove's far side sits 7 + 18 1/4 = 25 1/4 in (641 mm) from the side wall.
- Pad width. 6 in each side: 18 1/4 + 6 + 6 = 30 1/4 in (768 mm). On the side wall's side, the pad stops 1 in (25 mm) short of the wall.
- Pad depth. The pad runs from the back wall to 6 in past the front: 5 + 23 3/4 + 6 = 34 3/4 in (883 mm).
- The pipe. It leaves the back through a wall thimble and keeps 1 in from anything that burns, by DuraVent's listing.
So the stove and its pad take a patch of floor 31 1/4 in (794 mm) out from the side wall and 34 3/4 in (883 mm) out from the back wall.
Now hold an unlisted radiant wood stove of the same size against the same figures: it takes 36 in at the back, so its front sits 59 3/4 in (1.52 m) out. The front zone runs another 36 in, to 95 3/4 in (2.43 m). Its far side sits 36 + 18 1/4 = 54 1/4 in (1.38 m) from the side wall.
| Case | Back wall to stove | Back wall to the end of the zone | Side wall to far side |
|---|---|---|---|
| Castle Serenity | 5 in (127 mm) | 34 3/4 in (883 mm), end of the pad | 25 1/4 in (641 mm) |
| Unlisted radiant wood stove, same size | 36 in (914 mm) | 95 3/4 in (2.43 m), end of the 36 in front zone | 54 1/4 in (1.38 m) |
The pellet stove needs about a third of the depth. The rest of the floor is then free for seats, set out in seating layout dimensions. Castle still says to keep "clothing and other flammable materials" off and away from the stove.
In a garage: where the air comes from and where the vent ends#
None of the five makers here bans a pellet stove from a garage in so many words, but they do limit it, and two of the limits are about air.
Combustion air. Englander and PelPro say never to draw outside air from an "enclosed space such as an attic, garage or crawl space."
The vent end. Castle, Comfortbilt and PelPro say not to end the vent "in any enclosed or semi-enclosed area" such as a carport or garage. In an attached garage, the vent has to leave the building, not the room.
The 18 in ignition rule. IRC M1307.3 says appliances "having an ignition source shall be elevated such that the source of ignition is not less than 18 inches (457 mm) above the floor in garages." A pellet stove lights itself with an igniter. The rule does not name pellet stoves, so ask the building official how they read it. The same rule comes up in garage heater mounting height.
Vehicles. IRC M1307.3.1 bars any appliance where a vehicle can damage it, unless barriers protect it. Keep the stove, its pad and its pipe out of the bay and the door swing in car parking space dimensions.
The house wall. The wall between a garage and the house is a fire separation. A pipe through it is a bigger question than a pipe through an outside wall, as garage to house door and step explains.
Where these figures stop applying#
These figures are for freestanding pellet stoves against a combustible wall in a US home, read from the seven manuals named here and the 2021 IRC. Your town may amend the code, so check with the building department. Your own stove's label outranks every number on this page.
They do not cover pellet inserts in a fireplace, corn or multi-fuel settings, or pellet boilers and furnaces. Englander, Castle, PelPro and Comfortbilt say never to put their stoves in a sleeping room. A mobile home has its own rules: outside air, a ground wire to the frame and bolts to the floor, set out in each manual. Quadra-Fire also sets alcove limits for the Mt. Vernon AE: 43 in (1.09 m) high at least and 36 in (914 mm) deep at most. Harman's P43 is not in the table, because no copy of its manual could be fetched to check.
Clearance is one fire figure among several. A stove at the right gap can still cause harm through a blocked vent, a bad seal or a missing carbon monoxide alarm. Other fuel-burning equipment has its own gaps, in water heater and boiler clearances, the codes are in standards and codes, and the unit converter handles the metric.
Frequently asked questions#
How far does a pellet stove have to be from the wall?
As far as its label says. Seven stoves checked here ask 0 to 5 in (0 to 127 mm) at the back and 6 to 13 in (152 to 330 mm) at the sides. Englander's 25-CB120 and 25-CBPAH can touch the back wall, and PelPro's PP130 wants the most at the side. The vent pipe may push the stove further out than the stove itself needs.
Can a pellet stove be placed against a wall?
Some can, at the back. Englander's 25-CB120 and 25-CBPAH list 0 in from the back wall. Englander still warns that the gap may need to grow to give the vent pipe its own clearance. None of the seven sit at 0 in on a side, where the least is 6 in (152 mm).
Why can a pellet stove sit closer to a wall than a wood stove?
Because it was tested and the gap was measured. The 36 in (914 mm) figure is the old NFPA 211 rule for a stove with no label. A lab test sets a listed stove's own gap from how hot the wall gets. A pellet stove also burns a small, metered fire and blows most of its heat out of the front.
How much clearance does pellet vent pipe need?
DuraVent's PelletVent is listed for 1 in (25 mm) to combustibles in the US and Canada. Stove makers often ask more from their own outlet: Comfortbilt 2 in (51 mm) from the back and side walls, PelPro and Quadra-Fire 3 in (76 mm) from the back wall. Use the larger of the stove's figure and the pipe's.
How big does a pellet stove hearth pad need to be?
6 in (152 mm) in front on all seven, measured from the glass on three. The sides take 6 in on most and 2 in (51 mm) on PelPro and Quadra-Fire. Add the stove's width and depth. A Castle Serenity, 18 1/4 in wide, needs a pad at least 30 1/4 in (768 mm) wide.
Does a pellet stove need a hearth pad on concrete?
Not for embers. Englander's 25-PDVC says a brick or concrete floor needs no floor protection. Its 25-CB120 adds that a concrete floor must have an R-value of 0.2 or more, and gives a concrete basement floor as its example. A timber floor, carpet or vinyl always needs the pad.
Can you put a pellet stove in a garage?
None of the five makers here bans it in words, but each limits it. Englander and PelPro say never to draw combustion air from a garage. Castle, Comfortbilt and PelPro say never to end the vent inside a garage or carport. IRC M1307.3 asks for any ignition source 18 in (457 mm) above a garage floor, so ask your building department first.
Can a wall shield reduce pellet stove clearance?
Almost never. IRC M1306.2.3 bans any cut by shielding for a solid-fuel appliance listed at 12 in (305 mm) or less, and lets none go below 12 in. Every figure here is 12 in or less except PelPro's 13 in side, which a shield could cut by 1 in at most.
Sources and standards referenced#
- 25-CB120 installation and operation manual (05/2016) England's Stove Works (Englander)Tested to UL 1482-00 and ASTM E 1509; unit to side wall 10 in, rear wall 0 in, corner 10 in; rear may need to increase for vent clearances; US floor protector 6 in front and sides, 4 in rear, R-value 0.2 or more; concrete basement floor needs none; never draw outside air from a garage; not in a sleeping room
- 25-PDVC / 25-PDVCH installation and operation manual Englander (Stove Builder International)Certified to ASTM E 1509 and ULC S627; 6 in to a side wall, 3 in to the rear wall, follow the vent maker's clearances too; floor protector 6 in front and sides, ember protection only, no R-value; none on brick or concrete; Canada 450 mm front, 200 mm sides and rear; 3 in from the outside wall once through it
- Serenity pellet stove operator's manual, P/N 12740 Rev 3 (05/01/13) Castle Pellet StovesTested to UL 1482 and ASTM E1509; clearances set by the ASTM testing lab: 5 in rear, 7 in side, 5 in corner; 18.25 x 23.75 x 34 in; floor pad 6 in front and sides, 2 in behind (floor figure), 24 gauge sheet metal minimum; room air blower circulates air around the heat exchanger; no vent ending in a garage or carport
- HP22 pellet stove owner's manual ComfortbiltHorizontal venting: back wall 2 in, side wall 7 in, rear corners 5 in; vertical: 2 in from back and side walls to the pellet pipe; floor protector 6 in in front of the glass and 6 in each side, 2 in beyond the flue pipe (Canada required, US recommended); no vent ending in a garage; not in a sleeping room
- PelPro PP130 owner's manual, 7086-171I (May 6, 2015) PelPro (Hearth and Home Technologies)Listed solid-fuel room heater, pellet type, ASTM E1509-12, OMNI-Test report 061-S-88-2; side wall 13 in; back wall 2 in horizontal, 3 in to the flue pipe vertical; corner 3 in; US hearth pad 6 in front from the glass, 2 in sides and back; never install in a sleeping room; no air from a garage
- Mt. Vernon AE owner's manual, 7034-276M (August 13, 2018) Quadra-Fire (Hearth and Home Technologies)Safety label: back wall 2 in, side wall 6 in, corner 2 in; vertical vent 8 in to the stove back, 3 in to the pipe; alcove 43 in high minimum, 36 in deep maximum; floor protector 6 in front from the glass, 2 in sides and rear
- International Residential Code 2021: M1306.1, M1306.2.3, M1307.3, M1307.3.1 (chapter 13) International Code Council, via UpCodes (Colorado)Label clearances govern; no shield cut for solid-fuel appliances listed at 12 in or less, none below 12 in for others; ignition source 18 in above a garage floor; no appliance where a vehicle can damage it unless barriers protect it
We cite published codes, industry planning guidelines and manufacturer specifications. Where a figure is our own recommendation rather than a published standard, the text says so. See how we measure.